Fabrikasi Peniti Bros Panjang 60 mm, Diameter 0,5 mm, Bahan AISI 1045, Kapasitas  40 Unit/Jam

Adib Fahrur Rozi; Syamsul Hadi; Dava Ilham Ibrahimovic; Muhammad Nashih Taufiqie; Bintang Bimantara Putra Pribadi; Mahesa Haryo Torayoga

doi:10.61132/mars.v4i3.1637

Authors

Adib Fahrur Rozi Politeknik Negeri Malang
Syamsul Hadi Politeknik Negeri Malang
Dava Ilham Ibrahimovic Politeknik Negeri Malang
Muhammad Nashih Taufiqie Politeknik Negeri Malang
Bintang Bimantara Putra Pribadi Politeknik Negeri Malang
Mahesa Haryo Torayoga Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/mars.v4i3.1637

Keywords:

0.3 mm Plate, 0.5 mm Diameter Wire, AISI 1045 Material, Fabric Pin, Punch and Die

Abstract

Problems that often occur in brooch pins are bent wire or detached from the hook, also the possibility of the brooch coming off the pin when worn as a problem encountered. The purpose of fabrication is to obtain a 60 mm long brooch pin, 0.5 mm diameter, AISI 1045 material. Fabrication methods include: brooch pin design; selection of AISI 1045 material for 0.5 mm diameter wire and for 0.3 mm plate; cutting wire 94 mm long and sharpening one end; cutting the brooch pin end hook plate; forming the wire into a circle with a 4 mm hole for one winding; cutting a 0.3 mm thick plate in the shape according to the design; forming a pointed end hook with a punch and die; pressing the base of the wire to one side of the shape plate; electroplating with Chromium solution material; ordering and installing the customer's taste brooch; unification between the brooch and the pin stem; and quality-dimensional inspection. The fabrication results are in the form of a 60 mm long brooch pin, 0.5 mm diameter, AISI 1045 material coated with Chromium with a total cost of IDR 290,-/piece and a production duration of 90 seconds/piece which means that the brooch pin can be used for various desired accessories.

References

Bleicher, F., Baumann, C., Krall, S., Mates, S. P., Herzig, S., Alder, T., & Herzig, N. (2021). Manufacturing technology considering the influence of heating rate, complex hardening and dynamic strain aging in AISI 1045 machining: Experiments and simulations. CIRP Annals: Manufacturing Technology, 70(1), 49–52. https://doi.org/10.1016/j.cirp.2021.04.083

Budi, E., Budi, A. S., Fitri, U. R., Aprilia, R., & Andriyani, D. (2021). Kajian sifat tetapan pegas dan modulus. Jurnal Pengabdian Masyarakat Sains dan Aplikasinya (JPMSA), 1(1), 1–6. https://doi.org/10.21009/jpm-sains.v1i1.18248

Catalucci, S., Thompson, A., Piano, S., Branson, D. T., & Richard III, I. (2022). Optical metrology for digital manufacturing: A review. The International Journal of Advanced Manufacturing Technology, 120(5–6), 4271–4290. https://doi.org/10.1007/s00170-022-09084-5

Dinata, R., & Habib, F. (2022). Pengaruh perlakuan panas baja AISI 1045 terhadap kekuatan tarik. Journal Technology Process (JTP), 2(1), 41–49.

Dohda, K., Yamamoto, M., Hu, C., Dubar, L., & Ehmann, K. F. (2021). Galling phenomena in metal forming. Friction, 9(4), 665–685. https://doi.org/10.1007/s40544-020-0430-z

Donati, L., Reggiani, B., Pelaccia, R., Negozio, M., & Di Donato, S. (2022). Advancements in extrusion and drawing: A review of the contributes by the ESAFORM community. International Journal of Material Forming, 15(3), 41. https://doi.org/10.1007/s12289-022-01664-w

Holmberg, J., Wendel, J., & Stormvinter, A. (2024). Progressive induction hardening: Measurement and alteration of residual stresses. Journal of Materials Engineering and Performance, 33, 7770–7780. https://doi.org/10.1007/s11665-024-09703-0

Holstein, V., Hermes, M., & Tekkaya, A. E. (2020). Analysis of incremental die bending of wires and tubes. Production Engineering, 14(2), 265–274. https://doi.org/10.1007/s11740-020-00952-1

Hwang, J.-K. (2022). Hardening and softening behavior of caliber-rolled wire. Materials, 15(8), 2939. https://doi.org/10.3390/ma15082939

Larsson, J., Pettersson, R., & Korin, C. (2024). Experimental and theoretical examination and development of methods to calculate required pull force in wire drawing. Heliyon, 10(19), e39867. https://doi.org/10.1016/j.heliyon.2024.e39867

Liewald, M., Bergs, T., Groche, P., Arno, B., David, B., & Martina, B. (2022). Perspectives on data-driven models and its potentials in metal forming and blanking technologies. Production Engineering, 16(5), 607–625. https://doi.org/10.1007/s11740-022-01115-0

Nota, N. A. S., Azis, A., Budianti, S. I., & Sampurno, C. B. K. (2025). Pengaruh proses quenching dengan variasi media pendingin terhadap sifat mekanik dan struktur mikro baja AISI 1045. Journal of Science & Engineering, 5(1), 140–144. https://doi.org/10.54199/pjse.v5i1.493

Okonkwo, B. O., Jeong, C., & Jang, C. (2022). Advances on Cr and Ni electrodeposition for industrial applications: A review. Coatings, 12(10), 1555. https://doi.org/10.3390/coatings12101555

Ren, Z., Fang, F., Yan, N., & Wu, Y. (2022). State of the art in defect detection based on machine vision. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(2), 661–691. https://doi.org/10.1007/s40684-021-00343-6

Rosidah, A. A., Setyowati, V. A., & Choir, M. (2021). Effect of current and coating time on the layer thickness and corrosion rate of electroplated AISI 1045. SPECTA Journal of Technology, 5(1), 99–104. https://doi.org/10.35718/specta.v5i1.337

Stahl, A. F. J., Selbmann, C. K. R., Kuhfuß, S. O. A. J. M. M. B., Behrens, B. A., & Groche, P. (2021). Strategies for residual stress adjustment in bulk metal forming. Archive of Applied Mechanics, 91(8), 3557–3577. https://doi.org/10.1007/s00419-021-01903-7

Suarsana, I. K., Astika, I. M., Suryawan, I. G. P. A., & Kurniawan, D. (2021). Efek perlakuan pack carburizing dan media korosif pada baja AISI 1045 terhadap laju korosi. Jurnal Energi dan Manufaktur, 14(2), 37–43. https://doi.org/10.24843/JEM.2021.v14.i02.p01

Toribio, J., & Lorenzo, M. (2022). On the use of multi-step dies for improving the performance against hydrogen embrittlement of cold drawn prestressing steel wires. Materials, 15(24), 9085. https://doi.org/10.3390/ma15249085

Wernicke, S., Hahn, M., Gerstein, G., Nürnberger, F., & Tekkaya, A. E. (2021). Strain path dependency in incremental sheet-bulk metal forming. International Journal of Material Forming, 14(4), 547–561. https://doi.org/10.1007/s12289-020-01537-0

Yuwita, P. E., Habib, A., & Faila, R. N. (2024). Studi pengaruh variasi media pendingin quenching dan waktu penahanan pada proses heat treatment terhadap kekerasan baja AISI 1045. Jurnal Rekayasa Mesin, 19(1), 77–84. https://doi.org/10.32497/jrm.v19i1.4960

Zhuang, X., Liang, M., Zhu, S., Zhu, Y., & Zhao, Z. (2021). Sheet bulk forming of thin-walled components with external gearing through upsetting using controllable deformation zone method. Chinese Journal of Mechanical Engineering, 34, 138. https://doi.org/10.1186/s10033-021-00664-2