Perancangan Alat Safety Device untuk Mencegah Kerusakan Komponen Akibat Engine Overheat
DOI:
https://doi.org/10.61132/mars.v3i4.960Keywords:
overheat, safety device, automatic shutdown, temperature sensor, microcontrollerAbstract
Engine overheating is a critical condition that can cause damage to internal components, reduce operational efficiency, and lead to overall system failure. The absence of an automatic protection system is one of the primary factors contributing to damage. This study aims to design and test a temperature sensor-based safety device that can automatically cut off the engine's working system when the temperature exceeds the safe limit. The method used is descriptive statistical analysis to evaluate the effect of independent variables (operational time duration and workload) on the dependent variable (coolant temperature). The system was tested through water heating simulation using an electric heater and controlled by an Arduino Nano microcontroller, a MAX6675 temperature sensor. Testing was carried out with variations in power load (150, 300, 450, 600, and 750 Watts) and operational duration (20, 40, and 60 minutes). Temperature data were collected and analyzed using ANOVA to determine the effect of load and time on temperature increase. The results showed that the temperature increased significantly with increasing power load, with temperatures approaching 100°C at loads ≥450 Watts in less than 20 minutes. The load variable shows a significant effect on temperature (p < 0.05), while the duration of time shows a nonlinear but not statistically significant upward trend. The safety device is proven to be able to automatically disconnect the system when the temperature reaches the specified maximum limit, thus effectively preventing engine damage due to overheating.
References
Boby Wisely Ziliwu, M. T. (2020). PERAWATAN DAN PERBAIKAN SISTEM PENDINGIN MESIN INDUK PADA KAPAL PERIKANAN. Jurnal Akselerator, 1.
Budi Saputro. (2020). ANALISIS KEANDALAN GENERATOR SET SEBAGAI POWER SUPPLY DARURAT APABILA POWER SUPPLY DARI PLN MENDADAK PADAM DI MORODADI POULTRY SHOP BLITAR. Jurnal Qua Teknika, 7.
Emmanuel Oladoyin, A., & Ogunsola, T. (2023). Design and Construction of Internet of Things (IoT) Based Generator Monitoring System Olaleye Olukayode Olusegun Design and Construction of Internet of Things (IoT) Based Generator Monitoring System. In International Journal of Innovative Science and Research Technology (Vol. 8, Issue 3). https://www.researchgate.net/publication/380345116
Fajarudin, A., Hasibuan, A., & Marginingsih, R. (2024). PENCEGAHAN OVERHEATING MELALUI EDUKASI PERAWATAN PADA KENDARAAN RODA DUA. An-Nizam. https://doi.org/10.33558/an-nizam.v3i2.9121
Gagas Gumilang, M., Radonov Simanungkalit, J., Apriyana, A., & Rahayu, M. (2019). Penentuan Keberhasilan Safety Device Pada Engine Caterpillar 3066 Sebagai Media Pembelajaran Mahasiswa Teknik Alat Berat. Prosiding Seminar Nasional Teknik Mesin Politeknik Negeri Jakarta, 1290–1295. http://semnas.mesin.pnj.ac.id
Halim, A., Halim, A., Mangkona, M., Mangkona, M., Taufik, M., Taufik, Muh., Saputra, A., & Saputra, A. (2021). PEMBUATAN SAFETY DEVICE COOLING DOWN AUTOMATIC PADA UNIT HEAVY EQUIPMENT DOZER D3K CATERPILLAR BERBASIS MICROCONTROLLER. POLITEKNOLOGI. https://doi.org/10.32722/pt.v20i1.3496
Haryadi, S., Haryadi, S., Hendriana, D., Hendriana, D., Nasution, H., Nasution, H., Nasution, H., Nasution, H., Baskoro, G., & Baskoro, G. (2020). Monitoring of Thermostat Performance in Heavy Equipment Diesel Engine Cooling System Using an Ultrasonic Flow Meter. Conference on Management and Engineering in Industry (CMEI). https://doi.org/10.33555/cmei.v2i1.39
Huda, E. N., & Zulfikar, Z. (2024). Design Of Overheat Detection Device On Vehicle Engine Through Monitoring Water Temperature Or Cooling Oil. NEWTON: Networking and Information Technology. https://doi.org/10.32764/newton.v3i2.4897
Khamdilah, A., & Kundori, K. (2020). Analisis Manajemen Perawatan Actuator Sebagai Safety Device Dalam Memproteksi Terjadinya Overspeed Pada Mesin Penggerak Utama Kapal. Dinamika Bahari, 1(2), 90–97. https://doi.org/10.46484/db.v1i2.211
Nurrahman, A., & Wahyudi, H. (2020). Perancangan dan Pembuatan Alat Uji Beban Generator Set Menggunakan Larutan Potassium Hydroxide dengan Mekanisme Rack and Pinion sebagai Penggerak. Jurnal Teknik Mesin (JTM), 07(1).
Pranondo, D., Ridho Akbar, A., Studi Teknik Eksplorasi Produksi Migas Politeknik Akamigas Palembang, P., & Corresponding Author, I. (2021). SISTEM PERAWATAN DAN PEMELIHARAAN GENERATOR SET 501-B DI PT TITIS SAMPURNA LPG PLANT LIMAU TIMUR PRABUMILIH. Jurnal Teknik Putra Akademika, 12.
Prasetia, H. H., Prasetia, H. H., Ema, E., & Ema, E. (2020). PEMBUATAN PROTOTYPE ALAT OVERHEAT WARNING EXHAUST GAS TEMPERATURE (EGT). https://www.semanticscholar.org/paper/4ff1d3455a5550f22a975de1382be523cdec6a26
Prasetya, P., Nazarwin, N., & Seno, A. (2022). Analisis Penyebab Terjadinya Overheat pada Main Engine di Kapal Self Propelled Oil Barge Tirta Samudra XVIII. Jurnal Cakrawala Bahari. https://doi.org/10.70031/jkb.v5i2.50
Pratama, S. A. (2022). Pengoptimalan Perawatan Dan Pengujian System Safety Device Pada Mesin Induk Mitsubishi Di Tb. MBS 2000 1 PT. Alusteel Engineering Indonesia. Jurnal Universal Technic. https://doi.org/10.58192/unitech.v1i2.415
Ramadhan, R. F., Wanda, R., Nugraha, M. A. P., & Kelana, S. (2024). Analisis Perawatan Lub Oil pada Generator di Kapal KM. Tirta Samudra XXVIII. Jurnal Cakrawala Bahari. https://doi.org/10.70031/jkb.v7i1.61
Saihilmi, M. I., Saihilmi, M. I., Zaman, M., Zaman, M. B., Zaman, M. B., Zaman, M., Santoso, A., Santoso, A., Santoso, A., Santoso, A., Kusuma, I. R., Kusuma, I. R., & Kusuma, I. R. (2021). Developing of Emergency Safety Device Module Under Vessel Integrated Automation System for Dual Fuel Diesel Engine. IOP Conf. Series: Earth and Environmental Science. https://doi.org/10.1088/1755-1315/698/1/012013
Santosa, K. Y., Wichaksana, A., Ardiansyah, M., & Sulistyo, A. B. (2024). PENGARUH VARIASI CAIRAN PENDINGIN (COOLANT) TERHADAP POTENSI OVERHEATING PADA ENGINE DIESEL (STUDI KASUS MITSUBISHI L300). Berkala Forum Studi Transportasi Antar Perguruan Tinggi. https://doi.org/10.19184/berkalafstpt.v2i1.889
Studi Jaringan Telekomunikasi Digital, P., Negeri Malang, P., Hasan Fuadi, M., Wahyu Purwandi, A., & Hendra, R. Y. (2020). RANCANG BANGUN KONTROL DAN MONITORING SUHU PADA MESIN DIESEL MENGGUNAKANWEB MOBILE. Jurnal JARTEL, 10(1), 2654–6531.
Subhashini, G., Subhashini, G., Krishnan, S., Albanna, A. A., Abdulla, R., Albanna, A. A., Abdulla, R., Albanna, A., & Abdullah, R. (2020). Integrate for car brake failure and engine overheat system. Indonesian Journal of Electrical Engineering and Computer Science. https://doi.org/10.11591/ijeecs.v20.i3.pp%p
Wibowo, W., Astriawati, N., Permesinan Kapal, P., Tinggi Maritim Yogyakarta, S., Prodi Permesinan Kapal, A., & Tinggi Maritim Yogyakarta Jl, S. (2021). Optimalisasi perawatan sistem pendingin tertutup pada mesin diesel tipe MAK 8M32 Pada KM LIT ENTERPRISE. Jurnal Polimesin, 19.
Yuliyanti, F., & Prasetyo, I. (2020). IDENTIFIKASI SISTEM PENDINGIN PADA MESIN DIESEL MITSUBISHI 100 PS. http://ejournal.politeknikmuhpkl.ac.id/index.php/surya_teknika
Zhu, K., Liu, J., Yan, Z., & Zhang, L. (2021). Starting System and Safety Protection of Explosion-proof Diesel Engine for Coal Mine Based on Compressed Air. Journal of Physics: Conference Series, 2108(1). https://doi.org/10.1088/1742-6596/2108/1/012005
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Mars : Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
