Pengaruh Dosage Duration dan Press Station Down terhadap Cacat Unmolded Produk Shoulder Extrusion Tube pada Proses Compression Moulding

Rizki Ahmat Yunifianto; Elka Faizal

doi:10.61132/mars.v2i5.313

Authors

Rizki Ahmat Yunifianto Politeknik Negeri Malang
Elka Faizal Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/mars.v2i5.313

Keywords:

compression moulding, dosage duration, short shot, shoulder tube, unmolded

Abstract

In the plastic molding industry, there is a compression molding process to make shoulder tubes for cosmetic products. This research was to determine the effect of dosage duration and press station down parameters on unmolded defects in shoulder extrusion tube products. This research method uses quantitative with an experimental approach. This method is carried out by varying parameter setting dosage duration of 0.25s, 0.30s, 0.35s and press station down of 4 bar, 5 bar, 6 bar. The result od the study found that the parameters of dosage duration, press station down and the interaction of the two variables have a significant effect on unmolded defects. The higher the dosage duration and press station down, the unmolded defects decrease as indicated by the average product weight meeting the standard. The lower two parameters, the more unmolded defects occur, indicating that the average product weight not meet the standard weight tolerance of good products.

References

Anwar, M. C., Budiyantoro, C., & Thoharudin, T. (2018). Optimalisasi Parameter Proses Injeksi Menggunakan Simulasi Moldflow untuk Meminimalkan Cycle Time dan Eliminasi Short Shot pada Produk Tempat. JMPM (Jurnal Material dan Proses Manufaktur), 2(1), 56-67.

Aribowo, M. S., & Dani, A. (2023). The Effect of Holding Pressure and Inject Pressure to Short Shot Defect in Injection Molding Cover Pot: Pengaruh Holding Pressure dan Inject Pressure Terhadap Short Shot Defect pada Proses Injection Molding Cover Pot. Logic: Jurnal Rancang Bangn dan Teknologi, 23(2), 147-154.

Fahrizal, A. (2021). ANALISA PENGARUH TEMPERATUR INJEKSI, WAKTU INJEKSI, DAN TEKANAN INJEKSI TERHADAP CACAT SHORT SHOT PADA PROSES CETAK PLASTIK. Malang: POLINEMA

Iskandar, N., Fajri, D., Vendiza, R., & Sudharto, J. (2019). ANALISIS CACAT SHORT SHOT DALAM PROSES INJECTION MOLDING PADA KOMPONEN SHROUD FAN. Prosiding SNST 10, 101-106.

Nur Hidayat, T. (2022). Pengaruh Tekanan Compression moulding Terhadap Kekerasan dan Densitas Daur Ulang High-Density Polyethylene (HDPE) Sebagai Kandidat Bahan Baku Ubin. Jurnal Ilmiah Momentum, 18(1), 52-56.

Park, C. H., & Lee, W. I. (2012). Compression molding in polymer matrix composites. In Manufacturing Techniques for Polymer Matrix Composites (PMCs) (pp. 47–94). Elsevier.

Suminto, S. (2017). Ecobrick: solusi cerdas dan kreatif untuk mengatasi sampah plastik. Productum: Jurnal Desain Produk (Pengetahuan dan Perancangan Produk), 3(1), 26-34.

Xie, J., Wang, S., Cui, Z., & Wu, J. (2019). Process optimization for compression molding of carbon fiber-reinforced thermosetting polymer. Materials, 12(15). J.P. Holman. 1986, Heat Transfer, Sixth Edition. McGraw-Hill, Inc., New York.

Yanto, H., Saputra, I., & Wiratno Satoto, S. (2018). ANALISA PENGARUH TEMPERATUR DAN TEKANAN INJEKSI MOULDING TERHADAP CACAT PRODUK. In Jurnal Integrasi | (Vol. 10, Issue 1)